delabs Circuits

Tuesday, June 10, 2014

Electronic Product Production.

a. PCB Assembly.

First Inspect PCB for hairline shorts and cuts and also traces of unwanted copper in the edges and repair them. Also Check if all Drill holes & Slots are proper size and PCB is Fitting in its Place properly, This is because Drilling and Filing should not be done after assembly as it causes serious reliability problems.

Second populate all the resistors, Jumpers, Diodes and Ceramic Capacitors these are tough components. Then Insert all Transistors, LEDs, Displays, Electrolytic Capacitors and IC s (Bases), Here care should be taken not to overheat any component as it may damage them. Lastly Solder Connectors, Relays, Coils and Transformers which may require a high wattage Iron, and Mechanical Reinforcements.

Electronic Product Production - delabs Technologies

b. Precautions during Production.
  • Observe Polarity for Diodes, El-caps, Connectors, etc.
  • Make sure of Pin 1 for IC s, Regulators, Transistors and Mosfets before insertion.
  • Avoid bases for ICs in production as these fail on use.
  • Make use of Electrostatic protection for CMOS devices.
  • When Cutting Leads use protective Goggles and do it in a separate place as the cut leads fly all over the place.
  • Use Iso Propyl Alcohol (IPA) as de-greasing agent on PCB.
  • Water & Detergent wash is very good but only if coils, Transformers, Relays are hermetically sealed- Impregnated.
Use a Lacquer-Varnish or RTV rubber coat on both sides of PCB including on the components to prevent corrosion and also it helps maintain accuracy-precision.

Lead is a kind of poison, use gloves or wash hands with soap after work is over. Flux, IPA, Thinner Fumes can cause respiratory health problems. Work in a ventilated area use Exhaust Fans and Open Windows. Dispose of Metal, Plastic and Chemical waste separately and well packed as these can contaminate the environment and also cause Injury.

Published online around - Nov 1999

Contents

Basic Electronics
Basics of Electronics
Product Production
Work Discipline
Testing Points
Learning Electronics
Electronics Theory

Production Notes
Prototype Fabrication
Electrical Circuits
Electromechanical


Library
Scots Guide Electronics
Engineering - Wikibooks
Design Lab - Jim Svoboda
DC Circuits UOG
Socratic Electronics
Blobz Guide Electric Circuits


Product Design
Product Development
Constant Current Source
Good Voltage Regulators
Insulation Resistance
Digital Insulation Tester
DN Schematic PCB 04
DN Product Design 07


Hobby Circuits
VU Meter Circuits
LED brightness control
555 Incredible Chip
Process Control
liquid level measurement
Thermocouples and RTD
Design ADC Interface uC
Thermocouple Amplifier
IA Instrumentation 02
Temperature on DMM
Optical Proximity Switch
Analog Mux - Data Acquisition


Test Measurement
Instrumentation Automation
NI Test and Measurement
DMM Digital Multi Meter
Oscilloscope in T&M
IA Automation 01
Build Instruments
Tektronix T&M Equipment
Educators Corner – Agilent


Power Electronics
UPS Background
Transformer Connections
DN Power Electronics 03
DN Power Electronics 02
Half Bridge Convertor SG3525


Embedded
Interfacing Microcontrollers
Embedded Process Control
80C31 8052 Microcontroller
Microprocessors and uC
Embedded Systems Design

Components
Good Voltage Regulators
Relays and Contactors
Potentiometers Trimpots
Prototype Boards Types
Types of Capacitors
Types of Switches
Resistors How they Work
Coils Transformers SMPS
Mains Transformers Types
DN Components Selection 05

Tutor Gadgets
Count-Up Timer
Digital Logic Gates
Electronics Tutors

History
Teaching Instruments
Charles Proteus Steinmetz
Muntzing a Circuit Design
Teralab Electronics projects
Historical Instruments


Tables, Charts, Videos
Binary and Hex
Resistor Color Code
Ohms Law
Giga, Tera, Pico, Nano
High Resistance Materials

Analog
School - Analog Design
DN Analog Basics 06
DN Op-Amps 01
TI Semiconductors