Saturday, September 06, 2014

Thermocouples and RTD Tables

The easiest way to measure temperature is with a glass diode like 1N4148 or a metal Transistor like 2N2222. These have a small temperature range, probably -5 to +120 is possible, but non-linear. A copper coil or any metal wire or even a wirewound resistor can work as temperature sensor but the thermal inertia makes it sluggish. IC semiconductor based sensors like LM335 and AD590 are easy to work with and pretty accurate. In industrial environment many types of Thermocouples, Pt-100 RTD and Optical Infra-Red Temperature measurements are used.

Input Levels for Thermocouples and RTD Pt-100. And the ways it has to be used. Thermocouples are selected on the basis on how they are mounted or fixed, the environment, the temperature range that is measured and finally the price you can afford for a particular application. Sometimes mechanical wear or chemical environments may eat away the sensors, so a cost-effective solution has to be evolved.

One customer wanted a special Pt-PtRh very high temperature sensor for molten aluminum. It was very difficult and costly to even arrive at a solution. So a non-contact infra-red sensor may save lot of time-money and even reduce risk of injury.

Thermocouples and RTD Tables

For J, K, and T Thermocouple Read "Temperature" + Room Temperature for mV shown applied to equipment, eg....

If Room Temperature is 25 Deg C and mv applied is 10.777 for J Type STC1000 then reading should be 200 + RT = 225 deg C. The mV shown are for Reference Junction at 0 Deg C.

It would be better if you refer links below, The above table i made long ago, then a Scan with OCR later formatting. It could have errors.

Read More

Contents

Basic Electronics
Basics of Electronics
Product Production
Work Discipline
Testing Points
Learning Electronics
Electronics Theory

Production Notes
Prototype Fabrication
Electrical Circuits
Electromechanical


Library
Scots Guide Electronics
Engineering - Wikibooks
Design Lab - Jim Svoboda
DC Circuits UOG
Socratic Electronics
Blobz Guide Electric Circuits


Product Design
Product Development
Constant Current Source
Good Voltage Regulators
Insulation Resistance
Digital Insulation Tester
DN Schematic PCB 04
DN Product Design 07


Hobby Circuits
VU Meter Circuits
LED brightness control
555 Incredible Chip
Process Control
liquid level measurement
Thermocouples and RTD
Design ADC Interface uC
Thermocouple Amplifier
IA Instrumentation 02
Temperature on DMM
Optical Proximity Switch
Analog Mux - Data Acquisition


Test Measurement
Instrumentation Automation
NI Test and Measurement
DMM Digital Multi Meter
Oscilloscope in T&M
IA Automation 01
Build Instruments
Tektronix T&M Equipment
Educators Corner – Agilent


Power Electronics
UPS Background
Transformer Connections
DN Power Electronics 03
DN Power Electronics 02
Half Bridge Convertor SG3525


Embedded
Interfacing Microcontrollers
Embedded Process Control
80C31 8052 Microcontroller
Microprocessors and uC
Embedded Systems Design

Components
Good Voltage Regulators
Relays and Contactors
Potentiometers Trimpots
Prototype Boards Types
Types of Capacitors
Types of Switches
Resistors How they Work
Coils Transformers SMPS
Mains Transformers Types
DN Components Selection 05

Tutor Gadgets
Count-Up Timer
Digital Logic Gates
Electronics Tutors

History
Teaching Instruments
Charles Proteus Steinmetz
Muntzing a Circuit Design
Teralab Electronics projects
Historical Instruments


Tables, Charts, Videos
Binary and Hex
Resistor Color Code
Ohms Law
Giga, Tera, Pico, Nano
High Resistance Materials

Analog
School - Analog Design
DN Analog Basics 06
DN Op-Amps 01
TI Semiconductors