Wednesday, January 21, 2009

Instrumentation and Automation - 02

In Test and Measurement and Industrial Process Control a common factor is instrumentation. The measuring aspect is common to both. T&M instruments are used in Testing, Research,Automated Testing, Troubleshooting and Servicing.

Instrumentation and Automation - 02

Process control Instruments are used in Production Lines made of Machines in a Factory. It could be Counters and Timers used for Textile or Steel Industry. It can also be Temperature and Pressure Controllers used in Oil Refining or Food Processing.

So you see a difference. We have handheld Test Instruments like DMM and Scope and We have Handheld Instruments for Gas Monitoring or Humidity too. In automated testings we have rack mount test instruments. In Control panels we have Rail Mount carrying DIN standard Instruments.
  • On-Off controls or level trip relays can oscillate if hysteresis dead band is very small or absent.
  • Hysteresis is like on at 300 off at 304 like in heaters or air conditioners. If you on-off at sharp 300 there is a chatter or oscillation. This is called dead-band in temperature control. In above example 304-300=4 is the dead-band.
  • LF356, TLO71 and CA3140 are FET input Op-Amps, the bias is in pA, The caps for sample hold with these opamps are low leakage ones.10uF tantalum for long time, low resolution data. Long hold times with 12 bit data (analog) use 1uF plastic multilayer and clean-IPA + coat PCB with epoxy.
  • Design the product in such a way that neither the pot terminals or pot switch is used for mains voltage, instead use the pot switch or variable resistance for signaling and the mains can be switched with Relay or Thyristor.
  • If you need a 10.00K resistor 0.1% and you only have 1% in the market, you can trim lower values to higher values by removing the paint of the resistor and scratching the black metal film till you get the desired value. (this is only for testing or prototype development, R&D, not for manufacturing).
  • 7107 and 7135 of Intersil can be tested in-circuit, check Vref for 100mV or 1V reference, then short Vin and Vref the reading should be 1000 counts for 7107 and 10000 counts for 7135. ground plane should be good, no ground loops, PCB only glass epoxy and low leakage caps to be used, then reading will be stable, use some coating on soldered PCB.
  • An electrically Noisy environment can be simulated with a hair drier, or hot air blower. Another way Looping the NC (normally closed) contacts of a 230V Electrical Contacter-Relay can make it oscillate, this makes a lot of Sound and more important is the Electrical noise rich in EMI-RFI. This helps basic testing of timers, counters, uP, uC and embedded systems as they may malfunction in noisy environment.
  • A Single Pole 12V 100mA relay in a feedback loop, with its contacts, can make a Electrical or Electromechanical Oscillator. This can test your ground loops and digital circuit decoupling caps. It simulates power spikes which may reset some counters.
  • When a Machine with many stages or even an entire production line has to be automated, a PLC system is easiest to configure. It has digital inputs for limit switches and proximity sensors, it has analog inputs for any other parameter sensor. The PLC output modules can drive Electrical Contactor circuits with 230V Signal or 4-20 mA for an AC drive. The tacho-generator voltage feedback or pulses feedback from a motor can be fed to PLC inputs too.
  • Automation is used to enhance the quality and quantity of the product, also where there is danger to operators or workers. This moves the worker up, into the maintenance and management of materials, machines and systems.
  • Industrial Automation is essential to enhance the manufacturing worker to deliver consistent, repeatable and timely delivery of products. Absence of automation makes quality and deliveries unpredictable and stresses worker on monotonous jobs. When the worker is creatively employed with his machine on automation, it is the best scenario.

Solderman Talks 1702 AD
"Over-Automation is an utopia which is incorrect. This is because if you have no workers in any factory, there are no consumers in that city. No consumers means no sales of goods, no building of houses, no buying of automobiles. All strata of People correctly employed, reasonably paid, seeds consumerism, promotes the economy and markets. Automate everything, economy grinds to an halt."

- Solderman Talks 1702 AD

Contents

Basic Electronics
Basics of Electronics
Product Production
Work Discipline
Testing Points
Learning Electronics
Electronics Theory

Production Notes
Prototype Fabrication
Electrical Circuits
Electromechanical


Library
Scots Guide Electronics
Engineering - Wikibooks
Design Lab - Jim Svoboda
DC Circuits UOG
Socratic Electronics
Blobz Guide Electric Circuits


Product Design
Product Development
Constant Current Source
Good Voltage Regulators
Insulation Resistance
Digital Insulation Tester
DN Schematic PCB 04
DN Product Design 07


Hobby Circuits
VU Meter Circuits
LED brightness control
555 Incredible Chip
Process Control
liquid level measurement
Thermocouples and RTD
Design ADC Interface uC
Thermocouple Amplifier
IA Instrumentation 02
Temperature on DMM
Optical Proximity Switch
Analog Mux - Data Acquisition


Test Measurement
Instrumentation Automation
NI Test and Measurement
DMM Digital Multi Meter
Oscilloscope in T&M
IA Automation 01
Build Instruments
Tektronix T&M Equipment
Educators Corner – Agilent


Power Electronics
UPS Background
Transformer Connections
DN Power Electronics 03
DN Power Electronics 02
Half Bridge Convertor SG3525


Embedded
Interfacing Microcontrollers
Embedded Process Control
80C31 8052 Microcontroller
Microprocessors and uC
Embedded Systems Design

Components
Good Voltage Regulators
Relays and Contactors
Potentiometers Trimpots
Prototype Boards Types
Types of Capacitors
Types of Switches
Resistors How they Work
Coils Transformers SMPS
Mains Transformers Types
DN Components Selection 05

Tutor Gadgets
Count-Up Timer
Digital Logic Gates
Electronics Tutors

History
Teaching Instruments
Charles Proteus Steinmetz
Muntzing a Circuit Design
Teralab Electronics projects
Historical Instruments


Tables, Charts, Videos
Binary and Hex
Resistor Color Code
Ohms Law
Giga, Tera, Pico, Nano
High Resistance Materials

Analog
School - Analog Design
DN Analog Basics 06
DN Op-Amps 01
TI Semiconductors