Thursday, January 15, 2009

Instrumentation and Automation - 01

  • If the waveform on the scope droops then you may need to use a 10X attenuating probe or mode. this attenuator is at the tip of the probe hence better measurement possible, also very high frequency signals may be best transmitted over a 50 ohm impedance matched line to the Oscilloscope. The History of Oscilloscope, Learn more about Oscilloscope from the Innovator of the Scope as a Measuring Instrument here is XYZs of Oscilloscopes.
  • Karl Ferdinand Braun - In 1897 he built the first cathode-ray tube...oscilloscope. CRT technology is to this day used by most television sets and computer monitors. The CRT is still called the "Braun tube".
  • Test a NPN transistor, DMM in 200K range. emitter negative probe, collector positive probe, it should show open. while still holding that way press wet finger on base and collector, it may show some reading, then it is ok. for PNP swap probes polarity and do the same thing. the wet finger when pressed applies a base current in uA.
  • Testing a Mosfet - Transistor Tester - Testing Transistors - Basic Testing of Semiconductor Devices
  • The most common reason of DMM failure is when a person tries to measure 230V AC with a DMM in current or ohms mode, with the probes in the wrong sockets. Use external attenuators and shunts.
  • A DMM in diode mode or resistance mode can be used to test IR diodes, take it under 100W lamp and measure, cover the IR diode and measure you will see a response in proper polarity.
  • If you put the DMM in 2V mode and measure the voltage across a ordinary LED near a 40W lamp you will see around 200mV. Turn off 40W lamp the mV will fall near 0. Even metal-can transistors with their top ground away will become photo sensors.
  • When you measure low voltages or high resistance like 1M with a DMM your body must not be in contact with the probe tips. Body resistance is low in comparison so error in reading or loading of mV from sensor, in sensitive and high impedance ranges.
  • Do not use an oscilloscope to measure 230V directly, use a transformer, differential probe or attenuator.
  • An oscilloscope 1M probe or a DMM 10M impedance can load circuits with nano-pico amps of bias.
  • Red socket and probe for positive and black socket and probe for negative
  • Is it oscillating ?.... We cannot say, it could also be DC, you need to see if a Clock is present. use a signal tracer or a DMM freq mode, or AC measurement. or build this solorb.com-elect-logprobe. When you do not have a scope you can build one for the PC.
  • Polarity and Zero Cross radio-flier.com-opamps.html see the last circuit it is a polarity indicator, which will tell you to swap the leads. VRS Zero Crossing detector circuit, Zero Crossing Detectors, Comparators, Discover Circuits - Zero Cross.

Testing Tools Resources

Contents

Basic Electronics
Basics of Electronics
Product Production
Work Discipline
Testing Points
Learning Electronics
Electronics Theory

Production Notes
Prototype Fabrication
Electrical Circuits
Electromechanical


Library
Scots Guide Electronics
Engineering - Wikibooks
Design Lab - Jim Svoboda
DC Circuits UOG
Socratic Electronics
Blobz Guide Electric Circuits


Product Design
Product Development
Constant Current Source
Good Voltage Regulators
Insulation Resistance
Digital Insulation Tester
DN Schematic PCB 04
DN Product Design 07


Hobby Circuits
VU Meter Circuits
LED brightness control
555 Incredible Chip
Process Control
liquid level measurement
Thermocouples and RTD
Design ADC Interface uC
Thermocouple Amplifier
IA Instrumentation 02
Temperature on DMM
Optical Proximity Switch
Analog Mux - Data Acquisition


Test Measurement
Instrumentation Automation
NI Test and Measurement
DMM Digital Multi Meter
Oscilloscope in T&M
IA Automation 01
Build Instruments
Tektronix T&M Equipment
Educators Corner – Agilent


Power Electronics
UPS Background
Transformer Connections
DN Power Electronics 03
DN Power Electronics 02
Half Bridge Convertor SG3525


Embedded
Interfacing Microcontrollers
Embedded Process Control
80C31 8052 Microcontroller
Microprocessors and uC
Embedded Systems Design

Components
Good Voltage Regulators
Relays and Contactors
Potentiometers Trimpots
Prototype Boards Types
Types of Capacitors
Types of Switches
Resistors How they Work
Coils Transformers SMPS
Mains Transformers Types
DN Components Selection 05

Tutor Gadgets
Count-Up Timer
Digital Logic Gates
Electronics Tutors

History
Teaching Instruments
Charles Proteus Steinmetz
Muntzing a Circuit Design
Teralab Electronics projects
Historical Instruments


Tables, Charts, Videos
Binary and Hex
Resistor Color Code
Ohms Law
Giga, Tera, Pico, Nano
High Resistance Materials

Analog
School - Analog Design
DN Analog Basics 06
DN Op-Amps 01
TI Semiconductors