Showing posts with label Process-Scanner-Alarm. Show all posts
Showing posts with label Process-Scanner-Alarm. Show all posts

Saturday, May 09, 2009

Analog Mux for Data Acquisition Systems

Here is a 4-20 mA In/Out Analog Mux with Cascade option. This is a simple circuit i designed to make a Automation System within a budget.


Analog Mux using 4051

This takes 4-20mA from many Transmitters and gives out just one 4-20 mA output. The Mux is done with a digital byte or word. This is a slow scanner as process is slow, that way many analog inputs can be multiplexed and sent into one analog input of a D/A. In near real time systems a faster mux could be used or mux totally avoided. This was made in some numbers, so the pcb is better than others.

4-20mA Multiplexer Circuit - pdf

Monday, November 10, 2008

Four Channel Temperature Alarm Docs

The temperature in a pipe is monitored with four RTD Pt-100 Sensors, The type of probe could be Extruder RTD probes with Bayonet or Compression Fitting, Get it from Omega. To keep costs low you can choose small thin film RTD sensors, they will be fast but on rough usage may break.

Design Documents
Source Files Orcad Format
The time taken to measure the temperature at the 4 points will be less than 4 seconds. An optional display of the measured temperature as shown above can be avoided by using a DMM to adjust the setpoint.

The Analog Timer Module can be set from 0- 30 minutes. If out-a remains high even after set time a out-b alarm goes on to sound a buzzer and flash a LED light.

Block Diagram :


Four Channel Temperature Alarm

It all started with a email from a client like this ..........

"I am looking at an idea for a circuit design; The idea is to sense a temp of 130 degrees and then light an LED and start a timer delay. The delay would be 3 min, after the delay if the temp is still above 130 sound alarm.

With the LED I would like to drive a counter display to show how many times the temp was sensed. I would like powered by 120vac and a 9 volt battery backup for counter circuit. If you can assist please let me know."

Monday, February 25, 2008

Multizone Process Scanner

This could take current or voltage inputs from many remote transmitters, 4-20mA or 0-1 V Inputs. Then it would display the calibrated value in a LED display. The Zone number was a digital display. This serves as a monitor of process values. It had a analog output with a digital channel byte-word output for interface with other instruments.

This uses the CD4051-52 for the analog switching. Operating this at +/- 7.5V gives best isolation from channels and low ON resistance. Now you have many types of devices to do this.

Multizone Scanner

When a large area or object has to be heated, many heaters are used. This device can monitor and display the temperature at various points. The Operator then can make adjustments in heating or cooling so that he can maintain Uniform temperature or a Temperature Gradient as specified by the Process.

There are many ways, these scanners are used. Many different parameters like pressure, temperature, level are measured with different sensors and converted to a 4-20 mA level using transmitters for each sensor. Then many parameters can be measured in one equipment, when it needs only periodic attention. As the scan rate can be set from 1 to 50 seconds, the operator will be able to keep a tab on the values or record it. This reduces the real estate required on the control panel. Then the control room can be small, as it has to be at a vantage point, with a birds view of the entire factory floor.

Industrial Process Control Circuits

Contents

Basic Electronics
Basics of Electronics
Product Production
Work Discipline
Testing Points
Learning Electronics
Electronics Theory

Production Notes
Prototype Fabrication
Electrical Circuits
Electromechanical


Library
Scots Guide Electronics
Engineering - Wikibooks
Design Lab - Jim Svoboda
DC Circuits UOG
Socratic Electronics
Blobz Guide Electric Circuits


Product Design
Product Development
Constant Current Source
Good Voltage Regulators
Insulation Resistance
Digital Insulation Tester
DN Schematic PCB 04
DN Product Design 07


Hobby Circuits
VU Meter Circuits
LED brightness control
555 Incredible Chip
Process Control
liquid level measurement
Thermocouples and RTD
Design ADC Interface uC
Thermocouple Amplifier
IA Instrumentation 02
Temperature on DMM
Optical Proximity Switch
Analog Mux - Data Acquisition


Test Measurement
Instrumentation Automation
NI Test and Measurement
DMM Digital Multi Meter
Oscilloscope in T&M
IA Automation 01
Build Instruments
Tektronix T&M Equipment
Educators Corner – Agilent


Power Electronics
UPS Background
Transformer Connections
DN Power Electronics 03
DN Power Electronics 02
Half Bridge Convertor SG3525


Embedded
Interfacing Microcontrollers
Embedded Process Control
80C31 8052 Microcontroller
Microprocessors and uC
Embedded Systems Design

Components
Good Voltage Regulators
Relays and Contactors
Potentiometers Trimpots
Prototype Boards Types
Types of Capacitors
Types of Switches
Resistors How they Work
Coils Transformers SMPS
Mains Transformers Types
DN Components Selection 05

Tutor Gadgets
Count-Up Timer
Digital Logic Gates
Electronics Tutors

History
Teaching Instruments
Charles Proteus Steinmetz
Muntzing a Circuit Design
Teralab Electronics projects
Historical Instruments


Tables, Charts, Videos
Binary and Hex
Resistor Color Code
Ohms Law
Giga, Tera, Pico, Nano
High Resistance Materials

Analog
School - Analog Design
DN Analog Basics 06
DN Op-Amps 01
TI Semiconductors