Showing posts with label Temperature-Controller. Show all posts
Showing posts with label Temperature-Controller. Show all posts

Monday, January 05, 2009

Blind Dial Analog Temperature Controller

This is a Low cost controller, Analog Dial Temperature Controller. It is also called Blind Controller. This essentially means Open Loop, just control the fuel or energy input to the system to regulate heat. This is not a Blind Controller that way, it only cannot display the temperature value, that could be another reason it is called blind.

Dial cyclic timers were used to control heat, these were purely mechanical clockwork devices. They could regulate well, when the material flow (liquid) is constant and mains power is regulated. But when the job to be heated, varies in quantity, control temperature is close to ambient or when a precise control is required; closed loop controllers are used. Even a thermostat is like closed loop, as the bimetallic sensor is temperature dependent. But not good enough.

This controller is closed loop, precision controller, only the digital display of temperature is absent. Fine one deg variations may not be easy in this.

Blind Temperature Controller

PCB Boards for Blind Controller -

Discussions -

Saturday, October 04, 2008

Two Setpoint Temperature Controller

A Two Point Process Controller or Temperature Controller would look like this. When a High-Low Alarm Protection for uC based Controller was needed the same was modified and used.

Sometimes uC based instruments just forget and that can be costly, the watchdog timer has solved this problem. In Industrial Process Control we cannot take any chances, so a two tier or even three tier protection is required, especially so if the Job or Raw material being processed is expensive. So Real Time Analog Trip + uC Controller is safe. Then you can still have Electro Mechanical Devices for Extra protection against Fire or Meltdown.

Two Setpoint Temperature Controller

Temperature is the most common process parameter, Pressure seems to be next. Flow, Level, RPM, Distance and many more follow.

When a physical parameter let us say distance is measured, we first need a sensor that converts it into electrical values, digital or analog. The sensor used for length is a Linear encoder and it creates the electrical information for the DRO to Display.

Now many sensors like a strain gauge produce very low and weak signals and some are non-linear. So the signals undergo Amplifying, Temperature compensation and Linearizing together called Signal Conditioning. This stage outputs some standard values like 4-20mA, 0-10 V, 1-5V, or even directly digital or wireless in the new technologies. Even when a digital interfacing standard is used, amplification and some signal conditioning is required at sensor end. Compensation and Linearizing can be better done with a uC using Math or Look up Tables.

When you have many different parameters then it is better to use process controllers with a 4-20mA input standard. Then the inventory of controllers can be reused for any process.

It is always better to use sensor-end transmitters to get 4-20mA to your Controller, Recorder or SCADA System.Weak signals are corrupted by noise and dont travel long wire distance. Junction EMF at joints and terminal blocks add to errors. These are overcome by the 4-20mA signal that has the juice and punch to transmit the data over the shop floor to the control panel rooms.

Read more here Temperature Measurement and Control

Sunday, June 01, 2008

Temperature Controller 48-96

A 1/8 DIN Indicating Temperature Controller. This is a Analog Controller built around ICL7107. Read more here Temperature Measurement and Control.
48 96 Temperature Controller
This is a 48-96 DIN Temperature Controller, it is mains operated, it is in a Industrial Plastic Housing. It is not meant for very harsh environments. Suitable for Control Panels in Control Rooms. It has a accuracy and linearity of 0.5%. It had options of on-off or time proportional control


Basic Electronics
Basics of Electronics
Product Production
Work Discipline
Testing Points
Learning Electronics
Electronics Theory

Production Notes
Prototype Fabrication
Electrical Circuits

Scots Guide Electronics
Engineering - Wikibooks
Design Lab - Jim Svoboda
DC Circuits UOG
Socratic Electronics
Blobz Guide Electric Circuits

Product Design
Product Development
Constant Current Source
Good Voltage Regulators
Insulation Resistance
Digital Insulation Tester
DN Schematic PCB 04
DN Product Design 07

Hobby Circuits
VU Meter Circuits
LED brightness control
555 Incredible Chip
Process Control
liquid level measurement
Thermocouples and RTD
Design ADC Interface uC
Thermocouple Amplifier
IA Instrumentation 02
Temperature on DMM
Optical Proximity Switch
Analog Mux - Data Acquisition

Test Measurement
Instrumentation Automation
NI Test and Measurement
DMM Digital Multi Meter
Oscilloscope in T&M
IA Automation 01
Build Instruments
Tektronix T&M Equipment
Educators Corner – Agilent

Power Electronics
UPS Background
Transformer Connections
DN Power Electronics 03
DN Power Electronics 02
Half Bridge Convertor SG3525

Interfacing Microcontrollers
Embedded Process Control
80C31 8052 Microcontroller
Microprocessors and uC
Embedded Systems Design

Good Voltage Regulators
Relays and Contactors
Potentiometers Trimpots
Prototype Boards Types
Types of Capacitors
Types of Switches
Resistors How they Work
Coils Transformers SMPS
Mains Transformers Types
DN Components Selection 05

Tutor Gadgets
Count-Up Timer
Digital Logic Gates
Electronics Tutors

Teaching Instruments
Charles Proteus Steinmetz
Muntzing a Circuit Design
Teralab Electronics projects
Historical Instruments

Tables, Charts, Videos
Binary and Hex
Resistor Color Code
Ohms Law
Giga, Tera, Pico, Nano
High Resistance Materials

School - Analog Design
DN Analog Basics 06
DN Op-Amps 01
TI Semiconductors