Showing posts with label Temperature-Docs. Show all posts
Showing posts with label Temperature-Docs. Show all posts

Saturday, December 13, 2008

Capacitor Temperature Monitor

When placing sensors in high pressure or vacuum chamber, they should be terminated by an epoxy sealed terminal block interface on the system. 4 wire RTD is best for such applications, as multiple terminations and junctions are involved; also the wires may have to run some distance.

When measuring temperature in a big surface or object, use multiple sensors. An indicating scanner-controller can be used or ensure cooling-heating is uniform using fluids or air circulation.

Zoom Image

Cooling Controller


RTD Sensors to Terminal Block Connections

W - is White Wire from RTD, R - is Red Wire from RTD, Color of Wire on RTD Sensor Pt-100.
Top 3 Terminals are for RTD 1 (Red), Bottom 3 Terms. are for RTD 2 (Yel), Marked with Color Tape.

The RTD two whites go to one end of the Platinum 100 ohms resistive sensor, the red goes to other end. The red in this sensor goes to gnd of opamp circuit in controller. Thru one white a 1mA current is injected, the other white gives a voltage output to opamp. This voltage after offset and calibration is proportional to temperature.

Thursday, October 02, 2008

Temperature Controller for Cooling Chamber

This is part of an user manual i used to give for cooling controllers - app007.pdf

Cooling Controller

Before you use a Controller to Cool a Chamber to Say +5 Deg C.

First :

Do not Connect the Controller. Directly Connect the Cooling Device e. g. : Compressor. to the system and check the maximum cooling it can produce. In case temperature goes to 0 deg or -10 deg then by using a STC1000 you can control at +5 deg.

But if directly you get cooling of only upto +10 deg then it is impossible for any controller to produce extra cooling, in such a case as this use a better compressor or more insulation.

Second :

Connect Sensor properly and replace when broken keep sensor close to the source of cooling.

Third :

Deadband (DB) at minimum is 1 Deg this is the best setting, maximum setting of deadband may increase compressor life and also save power but will produce a huge variation in temperature.

Fourth :

If large Variation of temperature is present and you need accurate control Reduce deadband to min.

Unit is factory set db at 1 deg, remove seal tape before dead band adjustment.

Wednesday, October 01, 2008

Temperature Control in Plastic Injection Molding

This is an Application note i used to give with my controllers - app009.pdf
Temperature Control in Plastic Injection Molding.
Temperature Control
Terms in Process Control and Explanation.
There are three Controls to be Adjusted to make a Proportional temperature Controller Perform Properly. This method has to be practiced and experience gained from it can be used to get very good and stable Control of the temperature or other process parameters.
1. Set Point. (SP) -

This is the Temperature at which you require the Heated area to be. Here we have to remember it is better to control the temperature of the metallic area closest to heater to avoid thermal Cushions. In Rubber and Plastic Molding if you are measuring the plastic temperature directly it may give rise to oscillations and proper control may not be possible.

In Controlling the Temperature of Air or Water (Bad Conductors of Heat) Forced Convection with Fans for Air or Stirrers for Liquids can be used when Sensing temperature of the Liquid or air directly. But in Plastic such things cant be done as it is a semi-solid when heated hence. Control of Temperature of the Metal Discharging Heat to the Plastic is most practical. Oscillations are inevitable if the sensor is away from heater or is in contact with a non-conductor of heat. Temperature Control Curve

2. Process Value. (PV) -

This is the Temperature at the Tip of the sensor or the material touching the tip of the sensor. In Non-Conductors of Heat like plastic if we are monitoring plastic at a certain point the temperature of the plastic will be very different at various points depending on the Distance of the Heater from that point due to thermal gradients.

3. Proportional Band or Dead band. (PB) -
Dead band or H % or Hysteresis are terms used in on / off Controllers in proportional controller we use the term proportional band.

The Temperature zone in which the Controller turns on or off The heaters in a time proportional manner is the proportional Band. Set Point 200 deg C It is Given in % e.g. 10% PB of 200 deg SP is 20 deg. the Heaters are on till 190 deg C and off above 210 deg. C. Between 190 to 210 is the PB. A little above 190 the Heaters are on for 90% time. A little below 210 Deg C the Heaters are on for 10% of the time. When SP=PV Process Value the Heaters are on for 50% of the time i.e. 50% Duty Cycle.
4. Cycle Time -
This is the repetitive rate at which the heaters are Turned on or off Room Temperature 26 deg C For a Cycle time of 12 Seconds, when PV=SP heaters are on for 5 seconds and off for 5 seconds and this goes on as long as PV=SP.
Tuning or Adjusting a Proportional Temperature Controller.
Step # 1 -
Ensure Sensor is properly connected to the Temperature Controller TC polarity reversal will show reducing reading in the Display as heat builds up. The Heaters used and wattage selected must be able to bring the temperature more than the maximum required control temperature with TC. If Supply Voltage is down or heaters are blown or not in contact TC can not solve the problem.

So when in doubt connect heaters directly to supply (without TC) and see observe maximum temperature e. g. if max. temp. is 500 deg C the TC can control temperature upto 480 deg C.

Step # 2 -

Keep PB in minimum position and power on system e. g. set temperature is 300 deg C. Now Observe maximum overshoot. and adjust proportional band as in table below.

SP 300 deg C

PV (Process Value or Measured Temperature)
PV overshoot Proportional Band
10 % 330 deg C or more Near Maximum fully clockwise till end.
5 % 315 deg C to 360 deg C Middle of the PB Control or towards max.
2% 306 deg C Little above present setting.
Less than 300 deg Droop e. g. 290 PB is Critically set Do not Change.

After each change turn on system again to see response till 2 % or less variation or overshoot or oscillations are obtained.

Thumb Rule ! -
  • Increment PB to Decrease Overshoot.
  • Increment PB to Decrease Oscillations.
  • Stop adjustment when PV droops < SP
  • Adjust EC to match SP = PV after PV is stable at a point less than SP.
Step # 3 -

There is an additional control called Error Cal EC ( manual reset or Integral) which is factory set for SP=PV 50% duty cycle. In certain cases after stable reading is obtained after adjusting or tuning PB the temperature may stabilize say at 290 deg for a set point of 300 deg the process is stable but a ten degrees process error is present. this can be compensated in two ways.
a. Increase setpoint to 310 deg the process settles at 300 deg but this may not satisfactory even if it is practical.
b. Adjust Error Cal provided in the back panel to increase temperature to 300 deg from 290 deg.
When this is done give some time for system to respond after every 1/2 a turn 180 deg of the control. the EC control is a Ten turn potentiometer like the SP potentiometer after 10 turns the direction of turning must change. Clockwise Increase temperature Anticlockwise decrease temperature. (at min. PB setting EC pot sets the On/Off Operating Point).
Temperature Control using SSR and STC1000PK.
SSR Heat Control
Mains Circuit -
Always Connect Phase to Live "L ", This Can Be "R" in a RYB System 3 Phase . "L" Live Can Be Verified by a "Neon Tester" . and it is the Energy Line (Tester Glows). "N" Neutral is the Energy return line and will be close to Earth Potential in a Neon tester it will not show a Glow. Earth "E" is the Local Earth at the site of the installation. ( "N" to "E" AC Voltage should be less than 5 Volts ideally)
SSR or Solid State Relay or Electronic Relay -

Generally this is a Thyristor Based Normally Open 230V Switch that can be turned on/off at a fast rate.
  • No moving parts hence no wear and tear.
  • Dissipates Heat when in On Condition.
  • Use adequate Heat Sink or SSR will fail.
  • Input to Output is optically isolated. very tight and crimped.
  • The one used here is DC Control AC 230V 15A Load SSR.
Components and Points -
  • Connect Power From Lighting (5 A) for Controller.
  • 1 Phase 230V Supply With Earth
  • Stainless Steel Braided (SSB) Sensor "K" Type ( SSB is Earthed )
  • Heater 1 kW and 15 Amps SSR
Fuse Rating of a HRC Fuse -

High Rupture Capacity (HRC) Fuse is Safe and Reliable. 10KW Heater at 230V is 10,000 / 230 in Amps of Fuse Rating. i.e. Watts = Volts x Amps hence use
50 Amps Fuse.
Relay Terminology -
  • C Common is connected to NC when Relay is off.
  • NO Normally Open is Disconnected when Relay off. (connected to C when Relay on).
  • NC Normally Closed is Connected to C when Relay off. (disconnected when relay on).
Relay outputs are Potential Free or Floating or at High Impedance.

Note - The Terminations of High Current Lines going to Heater must be very tight and crimped. Loose contacts will Spark and cause Fire.

Contents

Basic Electronics
Basics of Electronics
Product Production
Work Discipline
Testing Points
Learning Electronics
Electronics Theory

Production Notes
Prototype Fabrication
Electrical Circuits
Electromechanical


Library
Scots Guide Electronics
Engineering - Wikibooks
Design Lab - Jim Svoboda
DC Circuits UOG
Socratic Electronics
Blobz Guide Electric Circuits


Product Design
Product Development
Constant Current Source
Good Voltage Regulators
Insulation Resistance
Digital Insulation Tester
DN Schematic PCB 04
DN Product Design 07


Hobby Circuits
VU Meter Circuits
LED brightness control
555 Incredible Chip
Process Control
liquid level measurement
Thermocouples and RTD
Design ADC Interface uC
Thermocouple Amplifier
IA Instrumentation 02
Temperature on DMM
Optical Proximity Switch
Analog Mux - Data Acquisition


Test Measurement
Instrumentation Automation
NI Test and Measurement
DMM Digital Multi Meter
Oscilloscope in T&M
IA Automation 01
Build Instruments
Tektronix T&M Equipment
Educators Corner – Agilent


Power Electronics
UPS Background
Transformer Connections
DN Power Electronics 03
DN Power Electronics 02
Half Bridge Convertor SG3525


Embedded
Interfacing Microcontrollers
Embedded Process Control
80C31 8052 Microcontroller
Microprocessors and uC
Embedded Systems Design

Components
Good Voltage Regulators
Relays and Contactors
Potentiometers Trimpots
Prototype Boards Types
Types of Capacitors
Types of Switches
Resistors How they Work
Coils Transformers SMPS
Mains Transformers Types
DN Components Selection 05

Tutor Gadgets
Count-Up Timer
Digital Logic Gates
Electronics Tutors

History
Teaching Instruments
Charles Proteus Steinmetz
Muntzing a Circuit Design
Teralab Electronics projects
Historical Instruments


Tables, Charts, Videos
Binary and Hex
Resistor Color Code
Ohms Law
Giga, Tera, Pico, Nano
High Resistance Materials

Analog
School - Analog Design
DN Analog Basics 06
DN Op-Amps 01
TI Semiconductors