Solderman Basic Electronics

Basic Electronics, Practical Electronic Projects, Learning Circuit design, Electrical Fundamentals. Edutainment and Interactive Examples.

Search This Blog

Thursday, April 09, 2020

Digital and Embedded Systems Design

An Embedded Microcontroller or DSP system is made of Chips, Circuits and Firmware. The digital voltage levels, speed, bus width, fan out, power consumption are some factors that a designer has to keep in mind. As portable and wireless gadgets are becoming more popular, RF, Ethernet and Energy Efficient Design aspects should be studied. Power electronics and Analog Circuits knowledge is used around the system, all this is integrated to make an instrument, equipment or gadget.

Digital and Embedded Systems Design
  • 80C51 ports can sink more current but source very less, hence use a 10k pull up at all the ports or outputs.
  • Firmware must be developed in increments, tested in increments, backed up in increments, must be modular (include) reuse.
  • Tristate output, High Impedance and Floating all mean the same when it comes to IC Inputs-Outputs. It means the pin is insulated from rest of circuit in the IC. That means it will not influence the node or bus it is connected to. A DMM terminals are floating means that the hand held plastic DMM has no electrical conductive link to earth or ground.
  • You can use hyper terminal to upload code to single board computers 80C51 like in BINARY or ASCII. 
  • ASICs are for large volume production, or for products which have a long product life cycle.
  • Low volume production use FPGA or CPLD, or even flash based microcontrollers, so that all your inventory can be reused and recycled.
  • Cell phones or a LAN card ASIC is ideal as volumes are good in cell phones and for LAN cards the technology is matured. For either FPGA or ASIC's you get IP Modules or Code Libraries for many functions and applications.
  • Whatever the method keep design flexible and modular for reuse and to save cost. remember the hardware is difficult to alter, software can be altered even at customer site, flash has made this possible
  • In the future chips may be both analog and digital programmable with flash.
  • Unused CMOS inputs should have a pull up or pull down resistor, it should not float, or it oscillates.
  • Have a decoupling capacitor 104 that is 0.1uF or 100nF across the supply of every IC very near the IC supply pins.
  • A watchdog timer should be used in every microcomputer circuit like 8051 so that the system resets on hanging.
  • The reset on a microcomputer should be applied till the supply to it is stabilized, this will enable a clean start.
  • Analog ground (opamps), digital ground (CMOS) and power ground (relays and LED) should be separate, (linked at root)
  • Pull up or pull down resistors in TTL can be 10K and in CMOS 100K and in battery operated systems 1M.
  • CMOS gates and Opamps have a output drive capability of ~ 10-20mA, so when you drive a load say an LED use a series resistor to limit the current to 5mA to 10mA.
  • When the number of digital chips you use in a project goes above 20 or 30 then it is better to use PLD or CPLD types.
  • Try to use same family ICs in a circuit, like only LS or only HCT, if you mix up then you have to do a design review.
  • In a industrial environment many motors, DC drives and AC drives will be running, this will produce EMI, RFI, kickback spikes which cause microcontroller based equipment to hang. Use a watchdog timer for uC.
  • More EMI immunity by using opto couplers for all input and outputs, 4-20mA current signals for input and output and an isolated wide range SMPS.

Wednesday, April 01, 2020

Digital Count-Up Timer Gadget

Digital Timer Gadget Visual Interface - Here is is gadget GUI for Industrial Process control, WebApps. The buttons make a sound and Light up internal LED lamps. Power On-Off control, Digital Timer; Start, Reset Scroll and Select are the controls.

Screenshot

programmable-digital-timer

The advantage is that the industrial process or Home automation can be monitored and controlled on any computer including tablets which has a Browser. The plant automation or Home appliance can be regulated even as you travel back from factory to home. Or in any city from the Cyber Cafe. A Wireless Lan and Computer with Browser is all you need.

Watlow Reference and Guides

Louis Desloge Sr. founds Watlow Electric Manufacturing Company in St. Louis, Missouri, USA, to manufacture electric heating elements for the shoe industry. 1922

Watlow Sensors, Processing and Heaters

'Watlow designs and manufactures industrial heaters, sensors and controllers - all of the components of a thermal system."

 SERIES F4 Ramping Controller

The SERIES F4 1⁄4 DIN industrial ramping temperature controller meets the requirements of the most demanding ramp soak controller processing applications.

This ramping temperature controller features a four line, high-definition LCD interface display for quick and easy profile programming and controller configuration.

SERIES F4 Ramping Controller

Watlow reference data provides information for amperage conversions, thermocouple types, RTD tolerances and more.

Watlow Ltd- Reference - Guides and Tutorials

Watlow is the leader in engineering and manufacturing custom commercial electric heaters. ... offer electric heating elements, industrial heaters..